This is how to make face Mask guide. Face mask we know are very important especially at a time of virus spread like corona virus. It has become necessary that you learn how to make face mask with fabrics. Learn the steps involved in making your own face mask below and do use it appropriately.
Tools you will need to make face mask
Needle and thread (and a sewing machine, if you have one)
Pins or clips to hold fabrics in place (safety pins and paper clips will also work in a pinch)
Materials needed to make face mask
At least 20 by 20 inches of 100 percent cotton fabric, such as a flat tea towel
4 strips of cotton fabric for ties, about 18” long and ¾” wide
4 flat, clean shoelaces
Two flat (1/4”) sewing elastics that are 7” long each
The steps involved in making your face mask
Choose your piece of cotton fabric, prewash it on the warmest setting and dry it on high heat. (Tea towels are better to use than T-shirts or linens, according to the Stanford Anesthesia Informatics and Media Lab.)
Fold the fabric in half. Measure and cut out a 9.5” by 6.5” rectangle to create two identically sized layers. This is your mask base.
Now it’s on to the fabric ties.
Cut 4 thin pieces of material, about 18” long and ¾” wide. Fold each piece of fabric twice lengthwise, then once more to tuck the rough edges inside. Sew a straight line along the middle. This will prevent the fabric ties from having frayed edges.
ADDING THE TIES
Take one of your rectangular fabric layers. With the “right side” (or the outer-facing side, where the pattern might be) facing you, pin down the 4 fabric ties, one piece per corner. Make sure that the ties are gathered in the center of the fabric layer before advancing to the next step.
You can also substitute sewing elastic for fabric ties, but note that elastic cannot be bleached (and therefore, is not as easy to clean) and that anyone with a latex allergy cannot wear it. (Elastic is also increasingly in short supply.) Attach elastics to the first layer of fabric by securing the ends at the corners, forming little hoops. Make sure the elastic lies inside the perimeter of your fabric.
PUTTING IT TOGETHER
Take the second layer of fabric and line it up with the first. The “right sides” (or patterned sides) of the fabric should be facing each other, sandwiching the fabric ties or elastics. Secure the fabric sandwich together with pins.
Eyeball a midway point. From the middle, sew a straight line across the mask, about ¼” above the bottom edge of the fabric, toward the bottom left-hand corner. Remove any pins as you sew past them.
Make sure that the elastic or fabric ties are secured in the corners, sandwiched by your two layers of fabric, as you sew over their ends. You want to make sure your needle goes through the three pieces: the top layer, the end of the fabric tie, and the bottom layer. Add a couple stitches forward and backward (in both directions) to secure your ties in place.
STITCH ALL AROUND
Stitch all around the perimeter of the fabric layers, repeating the forward and backward motion at each corner to secure all the elastic ends or fabric ties.
Continue to stitch your way toward the starting point, but stop to allow for a 1 ½” gap.
Turn your project right-side out from the little 1 ½” gap. Your fabric ties or elastics should now stick out, like little legs.
Make three staggered pleats lengthwise on the mask, as if folding a paper fan. This helps the mask conform to the wearer’s face. Secure each pleat with pins.
With your pleats held in place by pins, stitch around the perimeter of the mask, ¼” away from the edge of the seam. This is called a top stitch. Take care when stitching over the pleats as the fabric may be quite thick.
Top stitch a second time around, about ¼” in from the first round of stitching. Now you have a completed mask.
Please remember to use your face mask appropriately as it isnt all about making face mask but using it the best way.
Source: I got more of the information including the images from https://www.nytimes.com/article/how-to-make-face-mask-coronavirus.html